8-Channel, 24-bit, fully isolated A/D board

(DNR-AI-218 shown in photo)

• For use in “CUBE” chassis
• 8 differential analog input channels
• 350 Vrms isolation (channel to channel and channel to chassis)
• Simultaneous sampling (one A/D converter per channel)
• Built-in anti-aliasing filters (@ 48% of sample rate)
• 120 kHz per channel sample rate (480 kHz board max)
• 24-bit resolution
• Gains - 1, 2, 4, 8, 16, 32 and 64

12-Channel, fully isolated RTD/resistance input board

(DNR-AI-222 shown in photo)

• For use in “CUBE” chassis
• 12 fully differential analog input channels
• 2, 3 and 4 wire connections
• 100 Ohm DIN and US measurements
• Channel-to-channel and channel-to-chassis isolation
• 0.005 °C resolution, 0.2 °C accuracy
• 0 to 40,000 Ω resistance measurement range
• Built-in 50, 60 and 400 Hz rejection (at select sample rates)
• 100 Hz, per channel sample rates

8-Channel, high voltage, fully isolated A/D board

(DNR-AI-288-300 shown in photo)

• For use in “CUBE” chassis
• 8 differential analog input channels
• &plusmin;300 VDC inputs
• 350 Vrms isolation (channel to channel and channel to chassis)
• Simultaneous sampling (one A/D converter per channel)
• Built-in anti-aliasing filters (@ 48% of sample rate)
• 120 kHz per channel sample rate (480 kHz board max)
• 24-bit resolution
• Gains - 1, 2, 4, 8, 16, 32 and 64

8-Channel Strain gage Simulator Board

• 8 Simulated strain gages
• Configured as Full, Half or Quarter bridge
• 120, 350 and 1k Ohm standard configurations
• AC or DC excitation
• >250 kHz bandwidth
• Wide ±15 V excitation range
• On-board A/D converter monitors excitation voltage

12-Channel Electromechanical Relay Output Layer

• For use in DNA series Cubes
• 12 independent Form C (SPDT) relays
• 150 VAC contact ratings
• 200 mOhm resistance (not including cabling)
• 2 Amp @ 30 VDC, (continuous)
• 750 mA @ 120 VAC (continuous)
• 125 Hz switching rates
• Available with output current/voltage readback (see DIO-462)

Guardian™ 12-Channel Form C Relay Output Board

• The Guardian Advantage
  • Programmable overcurrent protection (50 mA to 2 A)
  • Programmable overcurrent duration limits
  • Monitors each channel’s output voltage and current allowing Automatic detection of shorts/open and other system failures
• 2 A continuous output current at 30 VDC
• 750 mA continuous output current at 150 VAC
• 200 milliohm on resistance
• Output throughput rate of 125 updates per second

10-Channel Electromechanical Relay Interface

• For use in DNA Cubes
• 10 independent Form C (SPDT) electromechanical relays
• 140 VDC or 150 VAC (maximum operating voltage)
• 5 A @ 125 VAC (continuous rated load)
• 5 A @ 30 VDC, (continuous rated load)
• 8 A on-board protection fuses
• NOTE: This board uses a special high-current “D” connector and requires special Cables and/or Screw Terminal Panels

IRIG-A, B, E and G Timing Generation and Synchronization board

• IRIG-A, B, E and G output allows cube to provide timing signals
• IRIG-A, B, E and G input allows cube to synchronize with external IRIG-A, B, E and G sources
• Modulated or DC level inputs and outputs
• 1 PPS output
• Event input captures timing to UTC
• DNA-GPS input
• 10 MHz, 1 ppm time base or slaved to external 10 MHz
• DNA-CBL-650 cable (included with purchase) provides BNC connections for Clock/IRIG signals and 37-pin connections for other I/O

5-layer enclosure; room for 3 I/O layers; CPU + GigE/1000Base-T NIC; PowerPC 400 Mhz CPU; 24V (100 W) power supply, and FAN option

• Slots for 3 I/O boards
• Over 30 different I/O boards available
• Two independent Gigabit (1000/100/10Base-T) Ethernet Interfaces One port for Control, the second for diagnostics
• Two USB 2.0 ports (one controller & one slave)
• Inter-Cube sync interface
• Rugged: 50 g shock, 3 g Vibration, -40 to +70°C, 0 - 16,000 feet
• Compact: 4" x 4.1" x 4"
• Real-time: 1000 I/O scans in < 1 millisecond
• Complete Windows, Linux and RT OS support
• LabVIEW™, MATLAB®, DASYLab&trade, Simulink® support and more
• Standalone deployment as UEIPAC, UEISim or UEIModbus